DATASHEET 2N2219 PDF

The 2N, 2N, 2N and 2N are sili- con planar TO (for 2N and 2N) and in Jedec . This datasheet has been download from. Semelab encourages customers to verify that datasheets are current before Test Conditions. Min. Typ. Max. Unit. LAB. SEME. 2N IC = 10mA. IB = 0. Sep 2. Philips Semiconductors. Product specification. NPN switching transistors. 2N; 2NA. FEATURES. • High current (max.

Author: Metaur Mikagor
Country: Tajikistan
Language: English (Spanish)
Genre: Health and Food
Published (Last): 22 December 2012
Pages: 167
PDF File Size: 14.20 Mb
ePub File Size: 7.94 Mb
ISBN: 811-2-43004-469-7
Downloads: 29767
Price: Free* [*Free Regsitration Required]
Uploader: Nagore

Philips – datasheet pdf

This stage is called Saturation Region. In our case for a collector current of mA we have to pass a base current of 16mA. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. This resistor is connected to the base pin of the transistor to limit the current flowing through the base.

dataheet

Complete Technical Details ddatasheet be found at the datasheet given at the end of this page. However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor.

So to calculate the resistor value of the base we can use the formulae. Another important thing to keep in mind, while using datasehet transistor as switch is the base resistor.

2N2219 Datasheet, Equivalent, Cross Reference Search

As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on. Current Drains out through emitter, normally connected to ground.

Submitted by admin on 21 June When base current is removed the transistor becomes dayasheet off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle.

But this calculation will lead to the closest value to start with. To make this current flow through the transistor the value of base current I B can eatasheet calculated using the below formula: TL — Programmable Reference Voltage. The 2N is a NPN transistor and is normally used as a switch in many circuits. To make this current flow through the transistor the value of base current I B can be calculated using the below formula:.

The value of this current can be calculated by the required n22219 of current that will be consumed by the load.

2N Transistor Pinout, Specs, Equivalent & Datasheet

Here lets us assume the load here consumes around mA maximum so our collector current I C mA. To bias a transistor we have to supply current to base pin, this dataxheet I B should be limited to 5mA by using a transistor to the base pin. Amplifier modules like Audio amplifiers, signal Amplifier etc.

Current flows in through collector, normally connected to load. When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter.

Where h FE, is the current gain of the transistor which in our case is Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below. So the value if R B will be.

Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits. So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project.

Where Vcc is the voltage on which the load operates datsheet V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1.