1. Copyright © , Texas Instruments Incorporated. Data sheet acquired from Harris Semiconductor CDBE. ACTIVE. PDIP. N. Pb-Free. (RoHS). Buy TEXAS INSTRUMENTS CDBE online at Newark element Buy your CDBE Technical Datasheet: CDBE Datasheet. See all Technical. CDBE from TEXAS INSTRUMENTS >> Specification: IC, D-TYPE FLIP FLOP, DUAL, Manufacturer Part No: CDBE Technical Datasheet: (EN).
|Published (Last):||27 January 2008|
|PDF File Size:||15.1 Mb|
|ePub File Size:||1.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
Cd4013be datasheet configurations can be repeated by connecting the modules in series for getting the time period to any desired lengths, but in multiples of two. This pin receives the positive supply input, which must never exceed 15 volts DC. The sets of cd4013be datasheet change states when operated in the bistable mode or while setting and resetting the IC, always cd4013be datasheet opposite logic levels at any instant. Here we can see how the above discussed operating principle of the IC is practically set up for a useful purpose.
Pressing S2 now, just flips cd4013be datasheet status of the output to its cd4013bbe position. The IC incorporates two sets of identical, discrete data-type or D-type flip flop modules.
The testing is done with the following steps:.
Set and Reset Inputs Pins 4, 6 and 10, 8: You should find the following results:. The diagram illustrates how a IC may be set up for testing its cd4013be datasheet bistable operation and cd4013be datasheet it can be further applied for practical uses.
Understanding IC Pin-Outs and Specifications – Datasheet and Application Circuits Explained
Yet another important feature of the IC which enables cd401b3e bistable operation through two different inputs. D-type flip flops refer to circuits which may have a couple of outputs that change or toggle states in response to triggers cd4013be datasheet at the input terminals. This input is used for receiving clock cd4013be datasheet which are cd4013be datasheet in the form of square waves.
The testing is done with the following steps: After all the connections are made, have a quick glance and make sure that all have been wired as per the diagram, if possible brush-clean the solder side with thinner. Pin 7 is the ground or negative supply input of the IC. The signal may be applied externally through cd4013be datasheet transistor astable multivibrator or more conventional types using NAND gates or NOR gates.
cd4013be datasheet Following conventional safety standards, primarily these inputs also need to be assigned to a logic level, preferably to the ground terminal for the present IC, via sufficiently high value resistors. The signals produces a bistable effect over one of the free outputs, the other cd4013be datasheet connected to the Data input as explained above.
Clock Input Pins 3 and Terminate all the pin-outs as directed in the diagram by soldering the connections correctly. The IC can be also effectively used cd4013be datasheet switching any load through input signals cd4013be datasheet from a sound sensor.
Finally connect the circuit to the specified power input. Pinouts of the IC.
CDBE Datasheet(PDF) – Texas Instruments
Data Input Pins 5 and 9: Positive input Pin You should cd4013be datasheet the following results: Cd4013be datasheet D-type blocks consist of four inputs, explained as follows:.
As the name suggests, the IC is primarily used as a bistable for toggling the output stage of a particular circuit, and it is fundamentally incorporated in most electronic circuits.
Gently adjust and fix the IC on the veroboard somewhere over the center of the board by soldering. The cd4013be datasheet up shown can be simply built with the help of the diagram.
For other configurations this input is terminated to any cd4013be datasheet the logic levels, i. Complementary Ouputs Pins 1, 2, and 13, Pinouts of the IC The D-type blocks consist of four dataasheet, explained as follows: Procure the parts shown in the figure, along with the veroboard, cut into the specified cd4013be datasheet.
The astable clocks cd4013be datasheet be witnessed through LED1. The circuit shown can be used for toggling any load simply by touching the touch pad.